Filter
Top Products
Index - 1
INDEX
[Number]
1-2 phase excitation system
(explanation of terms) ...................... Appendix-27
1-axis fixed-dimension feed control .............. 9-29
1-axis linear control ....................................... 9-23
2-axis circular interpolation control with auxiliary
point designation ........................................... 9-33
2-axis circular interpolation control with center
point designation ........................................... 9-39
2-axis fixed-dimension feed control
(interpolation) ................................................. 9-31
2-axis linear interpolation control .................. 9-25
2-phase excitation system
(explanation of terms) ...................... Appendix-27
2-phase pulse (explanation of terms)
.......................................................... Appendix-27
2-speed trapezoidal control (explanation of terms)
.......................................................... Appendix-27
[A]
Absolute encoder (explanation of terms)
.......................................................... Appendix-28
Absolute position detection system
(explanation of terms) ...................... Appendix-28
Absolute position restoration function......... 12-47
Absolute system (explanation of terms)
.......................................................... Appendix-28
Absolute system ............................................ 9-14
Acceleration time 0 (
Pr.8
) ........................ 5-24
Acceleration time (explanation of terms)
.......................................................... Appendix-28
Acceleration time 1 to 3 (
Pr.26
to
Pr.28
)
....................................................................... 5-36
Acceleration time No. (
Da.3
) ..................... 5-59
Acceleration/deceleration process selection
(
Pr.35
) ......................................................... 5-38
Acceleration/deceleration processing function
..................................................................... 12-75
Acceleration/deceleration time change during
speed change, enable/disable selection (
Cd.35
)
..................................................................... 5-110
Acceleration/deceleration time change function
..................................................................... 12-42
Address (
Da.16
) .......................................... 5-78
Address (explanation of terms) ........ Appendix-28
Advanced positioning control execution
procedure ...................................................... 10- 6
Advanced positioning control ....................... 10- 2
After mode (explanation of terms) ... Appendix-28
Allowable circular interpolation error width
(
Pr.42
).......................................................... 5-43
Applicable system ........................................... 2- 6
Applic ation ....................................................... 1- 4
Arc address (
Da.6
) ..................................... 5-64
Auto tuning (explanation of terms) .. Appendix-29
Automatic trapezoidal acceleration/deceleration
(explanation of terms) ...................... Appendix-29
Auxiliary function ................................. 3-10, 12- 2
Axis error No. (
Md.20
) .................................. 5-86
Axis error occurrence time (Hour: minute) (
Md.21
)
........................................................................ 5-86
Axis error occurrence time (Second: 100 ms)
(
Md.22
).......................................................... 5-86
Axis feedrate (
Md.37
) ................................... 5-92
Axis in which the error occurred (
Md.19
) ..... 5-86
Axis in which the warning occurred (
Md.24
)
........................................................................ 5-88
Axis warning No. (
Md.25
) ............................. 5-88
Axis warning occurrence time (Hour: minute)
(
Md.26
).......................................................... 5-88
Axis warning occurrence time (Second: 100 ms)
(
Md.27
).......................................................... 5-88
[B]
Backlash compensation (explanation of terms)
.......................................................... Appendix-29
Backlash compensation amount (
Pr.12
) .... 5-28
Backlash compensation function ................. 12-11
Backup function (explanation of terms)
.......................................................... Appendix-29
Ball screw (explanation of terms) .... Appendix-29
Bank changing ................................................ 6- 3
Bias speed at start (
Pr.10
) .......................... 5-25
Bias speed at start (explanation of terms)
.......................................................... Appendix-30
Bipolar drive constant-current system
(explanation of terms) ...................... Appendix-30
Block No. being executed (
Md.55
) .............. 5-98
Block start (normal start)............................... 10- 8
Buffer memory address list .............. Appendix-55